Machine Features
- The leading edge Feeding.Four-axis Feeding Wheels system.Vacuum Suction System.
- Equipped With Skip(Discontinuous) Paperboard Feeding Function, Suitable relative big size boxes.
- Whole Machine Expansion sets tight links that can reduce wear and maintain long-term using without loose. Make sure Printing Chromatic accuracy.
- Touch Screen Input(Taiwan Fedak), Automatic Back to Zero, Automatic Reset, Saving Time And Saving Paperboards.
- Powerful Cylinder Full set Locking System to keep the machine works More smoothly.
- Start Delay Protection Device was equipped with the Main Motor, That is the Motor not will start if not all the units of the machine are locked well.
Electricity Automatic Control System Features
- More than 95 percent of the electrical Elements are International Famous Brand. The Control Center uses the Drive CNC positioning technology, there are Memory Parameters in the Lead Edge Feeding part, the printing part, the Slotting Part. Also With Memory Data Storage Function. If you stopped the machine when producing products, such as clean the slab rubber, and when you close the units again, and the data you had already set will be reset auto and you do not need set again, it saves time and paperboard.
- All units use the Pneumatic lock, electricity apart, the feeding wheels will stop when apart from the machine to make sure the printing accuracy next time.
Lead edge Feeder Unit
Lead edge Feeder System
- Vacuum Adsorption/suction, Leading edge of the feeder Structure.
- Baffle behind and Paper-sending board, side baffle are electricity adjustment.
- The Slide of the paper sending board are using Aluminum alloys structure, it makes the machine works smoothly and Steady, no shake at all.
- Steel Paperboard sending table is steel structure,40mm Thickness Steel wall durable.
- Automatic Paperboard Counting, Touch-Screen Input.
- In order to suitable for the large size paper boards, Electricity and air system been used for control skip-feeding, the customer can choose to continue or skip-feeding according to needs.
- The paper-boards lift uses the air cylinder adjusting system, also equipped with Inter-Lock Control switch in Slotting Unit/Stacker Unit to ensure Sudden Stop OR Recovery sending immediately.
Section Apart and Close
- Control the machine unit apart or close by Pressing Button and electricity Control, and also have the automatic alarm device.
- The Machine Units apart and close system use the pneumatic Control, and the machine is been locked by the Lead-feeding main cylinder lock on the Chain-Way.
Boards Feed Roller
- The Durable Rubber structure has been used on the upper paperboard-feeding roller.
- Paperboard Feeding down Creasing Embossing roller and hard chrome, durable and steady.
Back To “Zero”
- The machine equipped with computerized-setting Automatic back to zero, and also phase memory function, to ensure all the units have the same adjustment level, automatic setting the right place and automatic back to reset, save the papers.
Flexo Printer Features
Printing Cylinder
- The Printing roller diameter φ466mm (Including the slab rubber diameterφ480mm), Do hard chrome after been welding of the steel, shaft Center part quenched to make sure it toughness and not easily worn out, and also do Balancing correction.
- Adapt wheel fixed hangover Printing Plate, and equipped full layout and half layout hanging version slot. Suitable for a 3x10mm hangover Rubber Bar.
- Can use a foot-step switch to control the positive and negative move when assembling and disassembling the Printing plate.
Print Embossing roller
- The diameter is φ155mm, with hard chrome of the roller surface, also do Balancing correction.
- Printing lower Creasing roller, the distance can be adjusted manually, show in the scale, ranging from 0-12mm.
Boards Guide Axis
- The upper paperboard Feeding roller is solid steel, diameter φ150mm, equipped with 3pcs paperboard feeding creasing wheels.
- The wheel axis head uses one-way/Direction bearing structure, convenient adjustment of the upper creasing wheels.
- The down Paperboard Feeding diameter isφ155mm, with hard chrome on the surface, also do Balancing correction.
- The lower Creasing roller, the distance can be adjusted manually, show in the scale, ranging from 0-12mm.
INK ROLLER ODφ206.4mm
- The diameter is φ210mm, the material is high-quality seamless steel pipe. also, do Balancing correction.
- Durable Rubber on the surface, Cots and high parabola in the form of, after being the special grind, Ink transfer is perfect.
- The ink motor adopted with chain driven, when the Main Motor Of machine stop running, the Rubber Roller Slow-down Motor will keep working.
- the Distance with Anilox Roller, manual adjustment, figures showing on the dial, adjusting the range from 0-6 mm.
Anilox Roller
- Diameter is 215 mm, use a metal anilox roller, done the dynamic balancing correction.
- With time delay function, can automatic sequential lifting with the feed system.
- The distance With Printing roller can be adjusted manually, show in the scale, range from 0-6mm.
Registration Adjust
- With Planetary gear structure, the phrase can be adjusted correctly 360 degrees.
- Electricity phase adjustment, Digital show and also have memory storage function, you stopped the machine when producing products, such as clean the slab rubber, and when you start again, and the data you had already set will be reset auto to the original you set.
- Manual Adjustment for Left and Right move, range from 0-8mm.
- Electromagnetic brake mechanism has been used for fixing the Phase when machines apart or adjusting the phase, the brake system will limit the movement of the machine to make sure the printing rubber slab will not move.
Water Ink Supply system
- Equipped with Pneumatic Diaphragm Pump, Circulating, and steady supply water ink, easy to operate and simple to maintain.
- Stainless steel Ink Fountain.
Slotter Unit（Manual Adjust）
Creaser
- Top and Down creasing Wheels shaft diameter is 98 mm, made of solid steel, surface grand, after the hard chromium plating, grinding again, moving smoothly.
- The top creasing shaft surface covered with the rubber will do no damage to the cardboard, the rubber and creasing seat adopts the detachable type structure, is convenient to replace.
- The Down creasing Wheels Distance, is the manual adjustment, figures show on the dials; adjusting range is 0-12 mm.
Slotting knife Shaft
- Slotting knife shaft diameter is φ155 mm, surface grinding process, after the hard chromium plating, grinding again, moving smoothly.
- Upper slotting knife material adopt alloy steel, the width is 7mm, ground after heat treatment, the hardness is HRC60-63, toughness is better.
- Bottom slotting knife material is made of alloy steel, grinded after heat treatment; Hardness is HRC60-63, toughness is better.
- Side Slitting knife material is the same as slotting knife, upper blade Shape is V type whole circle, the bottom knife is a bi-plate, grind after heat treatment, the hardness of HRC60-63, the blade is sharp.
- Down Slotting knife Distance is the manual adjustment, figures show on the dial; Adjust range from 0-12 mm.
- Manual adjust for left and right side Moving.
Registration Adjusting
- Registration adjustment mechanism with planetary gear structure, 360 precision adjustments.
- Registration adjustment adopts electric control, digital display;
- Carton height is the manual adjustment, four knives are synchronous adjusted.
- Registration fixed with the electromagnetic brake mechanism, when the machine separation or adjust the Registration, the brake system can restrict the machine running and keep the former knife position fixed.
Others
- The light is equipped on the top of Slotting knife plate, easy for the work at Night.
- Interlocking control switch assembled on the feeding when abnormal printing or slotting can stop feeding.
Die Cutter Unit
Anvil Cover Cylinder
- The Anvil cover Rubber roller diameter is φ389mm (φ405mm Including the rubber), the material is high-quality seamless steel pipe. with hard chrome on the surface, And been Grinded also do Balancing correction.
- With Urethane rubber (De pair or American Brand) on the surface, with button up lock structure, easy to change.
- The Head of the Die cutting rubber slab use speed compensation unidirectional bearing structure which makes sure exact die cutting size (No speed Gap).
- The rubber roller with mechanical differential structure makes Manual sliding Left and right, range from 0-40mm both sides, it can make sure the Urethane rubber can been worn even, longer the service life.
- electrical adjustment of the rubber roller, digital display, ranging from 0-12mm.
- When adjusting the die-cutting knife or the knife back to zero, the die cutting rubber roller will lift up automatically, after been adjusted, it will go back again, avoid the Urethane rubber been damaged.
Die Cylinder
- The die cutting wheel diameter is φ432mm, the material is high-quality seamless steel pipe. with hard chrome on the surface, And been Grinded also do Balancing correction.
- There are Latitude and longitude lines on the die cutting wheels all sides positive/negative/left/right. With M10 standard Screw Holes.
- The height of the die cutting mold is standard Height=25.4mm, easy to made and install or Change.
- Equipped with Light up the die-cutting part, can see clearly at night.
Boards Guide Axis
- The upper roller is solid steel, diameter φ150mm, equipped with 4pcs Paperboard feeding Creasing pressing wheels.
- The diameter Of paperboard-Feeding Roller isφ155mm of the lower Paperboard feeding roller, with hard chrome on the surface, also do Balancing correction.
- The lower presser roller, the distance can be adjusted manually, show in the scale, ranging from 0-12mm.
Registration Adjust
- With Planetary gear structure, the phrase can be adjusted correctly 360 degrees.
- Electricity phase adjustment, Digital show and also have memory Storage function, you stopped the machine when Adjusting, the data you had already set will be reset auto to the original die cutting place you set.
- Manual Adjustment for Left and Right move, range from 0-8mm.
- Electromagnetic brake mechanism has been used for fixing the Phase, when machines apart or adjusting the phase, the brake system will limit the movement of the machine to make sure the die cutting mold will not move.
Stacker Unit
Platform Up and Down
- With the Optical system to control the platform lift, automatic up and down according to the height of the board’s stack, The motor has break function and also the safety device, make sure the place steady and fixed, not fell.
- Equipped with Powerful Hydraulic drive, the stack height can be up to 1600mm.
Boards Receiving Arm
- Pneumatic adjustment paperboard receiving arm.
- Individually adjust the belt, no limit of the Belt length. Belt Transfer.
Conveyor Belt
- Using Powerful Tooth Belt Drive belt to make sure enough Friction and service life.
Boards Receiving Baffle
- Cylinder adjustment.
- Assist paperboard-receiving, so it can receive without stop.
- When the paper boards reach the standard height, the clapboard will stretch out auto and hold the boards. The clapboard behind is adjusted by manual.
