Technical Data
|
1 |
Max. width |
1800mm |
2 |
Design speed |
220m/min |
|||||
|
3 |
speed for 3-ply |
180-220 m/min |
4 |
speed for 5-ply |
150-200 m/min |
|||||
|
5 |
speed for 4-ply |
100-160 m/min |
6 |
Order change speed |
120~150 M/ ( with splicer) |
|||||
|
7 |
Slitting precision |
±1mm |
8 |
Cutting precision |
±1mm |
|||||
|
9 |
Stacking height |
100~1700 mm |
10 |
Stacking size |
W1800*L3500 |
|||||
|
R E M A R k |
The above working speed run under the paper width1800mm and the reel paper requirement as below, together with heating temperature is about 160℃ . |
|||||||||
|
Should show idle running of machine of 250m/min after installation |
||||||||||
|
Liner grade |
120g/m2–180 g/m2 Compression strength (N.m/g）≥8 ( Moisture 8-10%) |
|||||||||
|
Flute grade |
100g/m2–150 g/m2 Compression strength（N.m/g）≥5.5 ( Moisture 8-10%) |
|||||||||
|
InsideLiner grade |
120g/m2–180 g/m2 Compression strength（N.m/g）≥6 ( Moisture 8-10%) |
|||||||||
|
11 |
Flute combination |
E B CA ：UVV Flute type (E/B/C/A), flute shape:UVV, four combination by user, flute parameter as attachment with signature by both parties. |
||||||||
|
12 |
Steam |
Max. Pressure 11kg/cm² |
Working Pressure 6-8kg/cm² |
Consume |
3000kg/Hr |
|||||
|
13 |
Power |
AC380V 50Hz 3PH |
≈400HP Install power |
Working power |
150~300HP |
|||||
|
14 |
Compress air |
9kg/cm² Max. pressure |
4-8kg/cm² Working pressure |
consume |
1m3/hour |
|||||
|
15 |
Install space |
≈Lmin90m* Wmin16m*Hmin6m (Actual size according to the drawings approval by manufacturer) |
||||||||
Single Facer
Main Component
| Process parameter | Specification | Material |
| corrugated roll | Φ360 | 48CrMo |
| Pressure roll | Φ370 | 45 |
| Glue roll | Φ260*∆30 | 45 |
| Doctor roll | Φ150 | 45 |
| FluteHeatroll | Φ450 | Q345R |
| Linear paper Heat roll | Φ450 | Q345R |
| Guide roll | Φ140 | 45 |
General Parameter
| Working width | Max 1800mm |
| Min 900mm | |
| Design Speed | 220m/min |
| Speed | 200m/min |
| Roll change time | 3Hour~5Hour |
| Steam | 10~12kg/cm² |
| Compress air | 4~8kg/cm² |
| Power supply | AC380V 50Hz 3PH |
Driver Parameter
| Width | 1800mm |
| Main motor | 50HP |
| Air blower motor | 20HP |
| Hydraulic system motor | NO |
| Glue roll motor | 3HP |
| Wiper roll gap adjustment motor | 1/4HP |
| Glue gap adjustment motor | 1/4HP |
| Optical wheel clearance adjustment | 1/4HP |
Mill Roll Stand
General Parameter
| Working width | Max1800mm |
| Reel diameter | Max1500mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Compress air | 4~8kg/cm² |
| Power supply | AC380V 50Hz 3PH |
| Vertical & horizontal movement | Hydraulic |
| Carriage& rail | Automatic |
| Brake | Four-point |
Driver Parameter
| Width | 1800mm |
| Motor for hydraulic system | 5HP |
Main Component
| Width | 1800mm |
| Rotary shaft | Φ245 |
| Clamp arm | L 135 |
| Vertical cylinder | Ø85*ST500 |
| Horizontal cylinder | Ø63*ST1100 |
Linear Pre-heater
General Parameter
| Working width | Max1800mm |
| Heater roll diameter | 900mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m* Wmax m*Hmax1.5m |
| Power supply | AC380V 50Hz 3PH |
| wrap angle | 3 0°~270° |
| Steam | 10~12kg/cm² |
Driver Parameter
| Width | 1800mm |
| Heater roll motor | 1HP |
| wrap angle adjustment motor | 1HP |
Main Component
| Name | Specification | Material | material heat treatment | Surface |
| Pre-heat roll | Φ900 | Q345R | Annealing | Grinding+chromium-plating |
| Guide roll | Φ130 | Q235 | Annealing | Grinding+chromium-plating |
Medium Pre-heater
General Parameter
| Working width | Max1800mm |
| Heater roll diameter | 900mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m* Wmax m*Hmax1.5m |
| Power supply | AC380V 50Hz 3PH |
| wrap angle | 3 0°~270° |
| Steam | 10~12kg/cm² |
Driver Parameter
| Width | 1800mm |
| Heater roll motor | 1HP |
| wrap angle adjustment motor | 1HP |
Main Component
| Name | Specification | Material | material heat treatment | Surface |
| Pre-heat roll | Φ900 | Q345R | Annealing | Grinding +chromium-plating |
| Guide roll | Φ130 | Q235 | Annealing | Grinding +chromium-plating |
Triplex Pre-Heater
General Parameter
| Working width | Max1800mm |
| Heater roll diameter | 1000mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m* Wmax m*Hmax1.5m |
| Power supply | AC380V 50Hz 3PH |
| wrap angle | 3 0°~270° |
| Steam | 10~12kg/cm² |
| Heater roll drive | Master drive |
Driver Parameter
| Width | 1800mm |
| Heater roll motor | 1HP |
| wrap angle adjustment motor | 1HP |
Main Component
| Name | Specification | Material | material heat treatment | Surface |
| Pre-heat roll | Φ900 | Q345R | Annealing | Grinding +chromium-plating |
| Guide roll | Φ130 | Q235 | Annealing | Grinding +chromium-plating |
Overhead Bridge Conveyer
| Working width | Max 1800m |
| Bridge ply | 5 layer |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m*Wmax m*Hmax m |
| synchronization | Frequency conversion |
| Tension | Auto sheet tension |
| Corrector | Autocorrector |
| Compress air | 4~8kg/cm² |
| Power supply | AC380V 50Hz 3PH |
Driver Parameter
| Width | 1800mm |
| Upload motor | (5HP+3HP)*2 |
Main Component(Suitable for width 2200mm)
| Process parameter | Specification | Material | materialheattreatment | Surface |
| Upright post | 150*150 | H-bar | Painting | |
| Crossbeam | 220#+140# | U-bar | Painting | |
| Guide roll | 45 | |||
| Pulleys | 45 | Annealing | Grindingchromium-plating |
Glue machine (Double)
Glue machine (Double)
| Working width | Max1800mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m* Wmax m*Hmax m |
| Glue rang | 0.08mm~1mm |
| Power supply | AC380V 50Hz 3PH |
| Compress air | 4~8kg/cm² |
| Glue roll mesh size | 32l ines |
| 35l ines | |
| Press | Twin roll Press roll |
| Steam | 10~12kg/cm² |
Driver Parameter
| Width | 1800mm |
| Glue roll motor | 5 HP*2 |
| Glue adjust motor | 1/2HP |
| Press roll gap adjust motor | 1/4HP |
Main Component
| Name | Specification | Material | Raw material heat treatment | Surface |
| Pre-heat roll | Φ452*3 | Q345r | Annealing | Grinding +chromium-plating |
| Doctor roll | Φ160 | 45 | Tempering | Grinding +chromium-plating |
| Glue roll | Φ290 | 20 | Tempering | Grinding+knurling+chromium-plating |
Double Facer
General Parameter
| Working width | 1800mm |
| Machine size | Lmax m* Wmax 3.6m*Hmax2.3m |
| Design speed | 220m/min |
Driver Parameter
| Width | 1800mm |
| Hydraulic drive motor | 5HP |
| wrap angle adjustment motor (option) | Not available |
| Hot plate | 2 air-cushion hot plate, 3 air-cushion hot plate ,4 air-cushion hot plate |
| Feeding pre-heat | pre-heat roll |
| Steam | 10~12kg/cm² |
| Compress air | 4~8kg/cm² |
| Power supply | AC380V 50Hz 3PH |
| Press | Adjustable air bag press plate, Spring press plate Gravity roller |
| Temperature control | Manual, Electrical |
Main Component
| Name | Specification | Material | Raw material heat treatment | Surface |
| Air cushion hot plate | 140*600*W | Q345R | Annealing | Grinding +chromium-plating |
| Common hot plate | 140*600*W | Q345R | Annealing | Grinding +chromium-plating |
| Hot-end gravity roll | Φ65 | 45 | Tempering | Grinding +chromium-plating |
| Pre-heater | Φ350 | Q235b | Annealing | Grinding +chromium-plating |
| Cool-end gravity roll | Φ65 | 45 | Tempering | Grinding +chromium-plating |
| Cool-end holding roll | Φ89 | 45 | Tempering | Grinding +chromium-plating |
| Pulley | Φ318 | Q235 | Annealing |
Main Driver
General Parameter
| Working width | Max1800mm |
| Drive roll diameter | Φ860mm |
| Design speed | 220m/min |
| Working speed | 200m/min |
| Machine size | Lmax m* Wmax4.3m*Hmax2.1m |
| Power supply | AC380V 50Hz 3PH |
| drive type | Dual shaft |
Drive Parameter
| Width | 1800mm |
| Drive motor | 100HP |
Main Component
| Name | Specification | Material | Material heat treatment | Surface |
| Drive roll | Ø860MM | Q235 | Annealing | Wear with anti-friction rubber |
| Gear | * | 20CrMnTi | Quenching | Grind |
| Belt tension wheel | * | Q235 | Annealing | chromium-plating |
Slitter Scorer(servo)
General Parameter
| Working width | Max1800mm |
| Working speed | 250m/min |
| Scoring width | Min0mm |
| Slitting blade QTY | 5blade |
| Setting speed | double ≈0S / single≈1S |
| Slitting width | Min135mm |
| Slitting accuracy | ±0.5mm |
| Size of machine | Lmax m* Wmax m*Hmax m |
| Power | AC380V 50Hz 3PH |
| Creasing accuracy | ±0.5mm |
| CreaserQTY | 8 creaser |
Drive Parameter
| Width | 1800mm |
| Slitting motor | 10HP |
| Scoring motor | 10HP |
Single Helical Cut Off
General Parameter
| Working width | Max1800mm |
| Design speed | 300m/min |
| Working speed | 250m/min |
| Cutting precision | ±1mm （stable speed ） |
| Machine size | Lmax m* Wmax m*Hmax m |
| Drive type | dual drive |
| Power supply | AC380V 50Hz 3PH |
| Geartype | helical gear |
| Cut type | Spiral |
Drive Parameter
| Width | 1800mm |
| Drive motor | 50HP*2 |
| feed in/out motor | 7.5HP |
Main Component
| Name | Material | Raw material heat treatment | Surface |
| Knife roll | SC45 | Grind | |
| Gear | 20CrMnTi | Tempering+ carburization | Grind |
Down Stacker
General Parameter
| Working Speed | Max1800mmmm |
| Design Speed | 220m/min |
| Compress air | 4~8kg/cm² |
| Power supply | AC380V 50Hz 3PH |
| Machine size | L m* W m*H m |
Drive Parameter
| Width | 1800mm |
| Feeding motor | 5HP |
| Up/down motor | 10HP servo motor |
| Paper discharge motor | 3HP |
| Docking motor | 1HP |
Control Cabinet(with wiring cabinet and operating station)
| Wiring cabinet | L m* W m*H m*6 Pcs |
| Operating station | L m* W m*H m*19Pcs |
| Power of double facer | 75HP□ 100HP■□ 125HP□ 150HP□ 200HP □ |
| Power of single facer | 40HP□ 50HP■ 60HP□ 75HP□ 100HP□ |
| Power supply | AC380V 50Hz 3PH |
